Poseidon's Realm: Media Reactors

Vertex Aquaristik Zeolith Filter Model ZF-15 With Pump

Reliable and functional design, assembled with high quality cast acrylic; Vertex™ Zeolith Reactors represent a constant endeavor to increase value without sacrificing quality.

Exclusive Features

  • Quality cast-acrylic construction for long life.
  • Robust PVC-welded outlet port.
  • Built-in check valve for on/off cycles.
  • True Union Ball Valve adjustment and uncoupling.

Technical Data

  • Footprint 9½" x 7"
  • Height 18½" (recommended 24")
  • Media Chamber Diameter 4"
  • Pump 290 gph @ 17W
  • Cast-acrylic construction
  • Rated up to 200 gal

$144.99

Precision Marine Kalkreactor KR620

At Precision Marine there are two ways Calcium can be added to your reef tank, the Calcium Reactor or the Kalkreactor pictured here. You can either gravity feed through the Kalkreactor from a freshwater top-off system to your reservoir, or use a dosing pump.

A reliable water pump is used in lieu of the magnetic stir bar, which tends to jam, bind and wear the acrylic.

This model also includes a threaded opening at the top to enable adding Kalk powder without removing the lid

$265.99

Two Little Fishies KW Reactor 300 (Kalkwasser Reactor)

The KW Reactor™ 300 creates saturated kalkwasser solution every time the feed pump is switched on to replenish evaporated water. Gentle mixing is achieved with a rotating sprinklerhead that is “powered” by the pressurized water feed

Technical Data
  • Capacity: Use with up to a maximum of 1 cup calcium hydroxide.
  • Aquarium Size: One reactor for aquariums up to 300 gallons (1135 Liters).
  • Recommended Pump Size: ca. 200 - 300 gal/hr (760 - 1140 L/hr). The pipes automatically reduce the flow to a small stream.
  • Connection for Hoses: 1/2 inch (12.7 mm) i.d. The inlet and outlet flexible 90° fittings rotate to suit your installation.
  • Approximate size: height: 15.25", width: 5". reactor diameter: 4"

$64.95

Deltec KM500 Kalkwasser Stirrer holds 500g Calcium Hydroxide

Kalkwasser - Translates from the German for limewater and is a solution made by dissolving Calcium Hydroxide in water. The resultant fresh solution is alkaline with a pH of 12.4 and contains a ready supply of both Calcium ions and Carbonate ions.
The solution reacts readily with CO2 in the atmosphere to form calcium carbonate and so it must be made in a relatively air tight environment which is where the kalkwasser stirrer comes in to play.

The KM500T is the standard stirrer suitable for tanks up to 1500 lts (350 UK gallons) and will produce up to 5lt of kalkwasser per hour.

Technical Data:
Can be stood on the outside of the aquarium or sump.
Must gravity feed back into the water supply.
Feed with RO water from a reservoir or direct from the RO unit.
Use in conjunction with a top up system.
Supplied with 500ml tub of RowaKalk.
Makes up to 5lt of kalkwasser per hour.

Dimensions:
L 150mm W 150mm H 480mm.
7.5V 3 watts consumption.

Suitability:
Suitable for aquariums up to 1500 lts (350 UK gallons

$495.99

Deltec FR1016 Fluidized Reactor

The FR1016 is better known as a Rowaphos reactor for its common use for fluidising Rowaphos however this quality reactor can be used for carbon or fluidising sand as a biological media.

Description:

The FR1016 is a substantial fluidized reactor with a twist off bayonet lid to allow easy access for replacement of the media. It is the taller version of the FR616. The water is forced down a central tube and is returned back up through a diffuser plate. Sponges are fitted either side of the media section to retain the finer particles.

The lid is fitted with a tap to adjust the flow and two hosetails connected to unions for simple removal or to allow hard piping to be used.

Capacity:

Suitable for up to 9.0 lts of media.

Flow rate:

Up to 2500 lt/hr (pump not supplied)

Dimensions:

300 mm x 250 mm x 1000 mm high (including fittings)

$795.99

NextReef MR1 XL Media Reactor

NextReef Reactors Loom Large Over the Competition! The MR1 families of Media/Substrate Reactors feature a massive 4-inch reaction chamber. The extra wide design maximizes water to media contact, increasing efficiency and minimizing dead zones in the reactor.NextReef Reactors have the largest capacities around, giving you the ability to run large amounts of media, or multiple products simultaneously. They`re ozone-safe, and perfect for phosphate control, de-nitrification or fluidized sand filtration. The NextReef MR1 stands over 23 inches tall... that's over two gallons, big enough for large reef systems - up to 600 gallons.

Specifications:
Recommended Tank Size: 600 gallons Marine / 1200 gallons Freshwater
Height: 23" Overall Height / 21" Reaction Chambers (585mm / 535mm)
Footprint: 12.5" x 6" (325mm x 150mm)
Reaction Chamber: 21" x 4" (Dual) (535mm x 100mm)
Total Capacity: 465 cubic inches / 2.0 gallons / 255 fluid ounces / 7.6 litre
Inlet / Outlet: 1/2" 90 Degree Barb Fittings - fits standard 1/2" ID tubing

$99.99

NextReef MR1 Monster Media Reactor

NextReef Reactors Loom Large Over the Competition! The MR1 families of Media/Substrate Reactors feature a massive 4-inch reaction chamber. The extra wide design maximizes water to media contact, increasing efficiency and minimizing dead zones in the reactor.NextReef Reactors have the largest capacities around, giving you the ability to run large amounts of media, or multiple products simultaneously. They`re ozone-safe, and perfect for phosphate control, de-nitrification or fluidized sand filtration. The NextReef MR1 stands over 23 inches tall... that`s over two gallons, big enough for large reef systems - up to 600 gallons.

Every NextReef Reactor is hand-crafted in the USA from the highest quality materials, and CAD engineered / CNC cut for a precise fit.

Specifications:
Recommended Tank Size: 600 gallons Marine / 1200 gallons Freshwater
Height: 23" Overall Height / 21" Reaction Chambers (585mm / 535mm)
Footprint: 12.5" x 6" (325mm x 150mm)
Reaction Chamber: 21" x 4" (Dual) (535mm x 100mm)
Total Capacity: 465 cubic inches / 2.0 gallons / 255 fluid ounces / 7.6 litre
Inlet / Outlet: 1/2" 90 Degree Barb Fittings - fits standard 1/2" ID tubing

$179.95

 

 

Copyright 2003-20 | Poseidon's Realm